CDL-165ETHGETHERNET/USB to HDMI/VGA Display ConverterOperation ManualOperation Manual
57. SOFTWARE INSTALLATIONThe following sections list the procedures to follow when installing the USB to HDMI and USB device drivers. Insert the provi
6When both the DisplayLink and USB Server drivers have been installed the USB Server’s icon should appear on the desktop and in the system tray.
77.3 Using USB ServerDouble click on the 'Launch USB Server' icon from the desktop or from the icon in the system tray and the USB Server wi
87.4 IP Property SettingWhen connecting PC/Laptop directly to the device or when the network has no DHCP server a special IP setting is required. Plea
9Click on the Network and Internet Connection and select Network Connections.
10Double click on the Local Area ConnectionDouble click on the Internet Protocol (TCP/IP)Click on “Use the follow IP address” and set the IP address a
118. USING DISPLAYLINK MANAGER8.1 Using DisplayLink ManagerAfter the driver is installed, a utility (DisplayLink Manager) will automatically appear in
12Color QualitySelect the screen color quality (available only in extended mode).Screen RotationRotate the screen on the additional monitor by 90, 180
13Extend toReposition the extended screen to the top, bottom, left or right of the primary display.ExtendSet the DisplayLink Manager to Extended mode.
14Set as Main MonitorSet the monitor to be the main monitor.Notebook Monitor offSet the PC/notebook's monitor off.
15MirrorSet the DisplayLink Manager to Mirror mode. You can see the same desktop image on the additional monitor.OffDisable the DisplayLink Manager on
16AdvancedOpening the Display Properties will allow you to adjust the resolution, color quality, position and refresh rate.8.2 Using More DisplayLink
179. UNINSTALL THE DEVICE DRIVERFollow the steps below to uninstall the Multi View driver. Step 1: Open the Control Panel: Start → Control Panel → Add
18Step 4: Click Yes to restart your computer.Then select DisplayLink Graphics and click Remove. Finally, select USB Server and click Remove.
1910. CONNECTION DIAGRAMHDMIVGAOFFHDMI OUTEDID AUDIOVGAOUTUSBLANDC 5VINPUTLAN IN USB PORTUSB INOROR TV/Monitor TV/MonitorWireless Ethernet HubNotebook
2011. TROUBLESHOOTINGSituation Check Point The device driver has been installed, but the DisplayLink Manager is not workingMake sure that the computer
2112. SPECIFICATIONSVideo Resolution Up to 1600×1200 /1920×1080 (wide)Video Input 1×Ethernet RJ-45, 1×USB 2.0Network Protocol TCP/IPVideo Output Po
2213. ACRONYMSACRONYM COMPLETE TERMARC Audio Return ChannelCEC Consumer Electronics ControlEDID Extended Display Identication DataHEAC HDMI Ethernet
Home page: http://www.cypress.com.twCYPRESS TECHNOLOGY CO., LTD
DISCLAIMERSThe information in this manual has been carefully checked and is believed to be accurate. Cypress Technology assumes no responsibility for
SAFETY PRECAUTIONSPlease read all instructions before attempting to unpack, install or operate this equipment and before connecting the power supply.P
CONTENTS1. Introduction ... 12. Applications ... 13. Package Contents
11. INTRODUCTIONThe device that can send audio/video signals from a Notebook/PC over a local area network through regular Ethernet cables to a TV whic
2whereas connection via USB supports Mac OS X (v10.4.11 and v10.5.6)• USB Port Extension: - An available USB 2.0 port with USB to mini-USB cable• N
36. OPERATION CONTROLS AND FUNCTIONS6.1 Front PanelUSBLANDC 5VINPUT LAN IN USB PORTUSB IN12 3 4 51 DC 5V Plug the 5V DC power supply into the unit an
46.2 Rear PanelHDMIVGAOFFHDMI OUTEDID AUDIO VGAOUT1 2 3 41 HDMI OUT Connect to the HDMI TV/display with HDMI cable for video and audio output.2 EDID
Comments to this Manuals